TWO-COLUMN BAND SAW MACHINE FOR ANGLE CUTS:     

440x600 HORIZONTAL

A semiautomatic machine hydraulically manipulated two- column machine, that is suitable for cutting steel constructions and profiles.  Warning: the machine is determined for cutting of long bars – in this case it is possible to cut to the left and to the right.  When cutting short pieces it is necessary to use angle cuts with adjusted arm to the left. We do recommend to use UPPER CLAMPING for angle cuts !
This machine makes angle cuts 60 grades to the right and 60 grades to the left.
It is suitable for serial production and thank to its robust construction enables to cut wide range of materials including stainless stells and tool steels both profiles and full materials. 

Construction:

• A rugged construction of machine including vice allows to take advantage of bimetal blades maximally.
• The arm of machine is conducted by linear bearing with a high loading capacity. This machine has pulleys from cast iron – diameters 500 mm.
• Working movement of arm between up and down position is regulated by microswitches.
• There is a vice with a long stroke hydraulic cylinder.
• Turntable with machined leading place of a basement for making angle cuts.
• Leading of blade is in hard-metal plates.
• The tension of blade is controlled automatically. 
• Manuall tension of band.  Accessoris: Hydraulic tension of band.
• There is a driven cleaning brush of a blade.
• Drive of machine is solved by worm gear box with maintenanceless oil filling. Three-phases electromotor  with double winding, with  a frequency converter  for a fluent regulation of the blade speed from 20 to 100 m/min. Sturdy flange with shaft. Termoprotection of engine.
• Cooling system for emulsion with liquid distribution to blade guides. 
• Robust base with a tank for chips.
• Indication of  blade tightening and opening of the cover
• Extenally situated controlling panel - its position does not depend on the position of turntable position when cutting angles.
• Controlling 24 V
• Maschine is equipped by hydraulic system that manipulates all functions of that maschine. It presses the arm to cut, pulls up the arm, opens and closes vices.

Basic equipement:

• Two rugged cylinders support material to be cut
• frequency convertor
• blade
• set of tools
• manual instructions

440-NPH	Hydraulic tension of band.
440-VTS	Worm chip extraktor.
BOX-PCS	Box for cutted pieces with emulsion draining to the waterproof tank.
BOX-TRI	Box for the chips with emulsion draining to the waterproof tank.
BOX-TAH	Tool for manipulation with BOX-PCS and BOX-TRI.
440-SRZ	Vice behind the cut. hydraulic clamping of the material behind the cut.
440-SKZ	Slide of cut pieces.
440-HPP	Hydraulical upper vice mounted on the main vice. Hydraulic upper clamping tighten the material in vertical sense by the hydraulic cylinder connected with the cylinder of the main vice.
440-PUH	Hydraulical side moving of bow with hydraulically locking of setting angle.
440-PUD	Digital indicator of adjusted angle.
440-RTS	Regulation press of vice.
440-RVP	Movable supporting cylinder for a basement of the machine.
MINI LUBE	Wasteless lubricating systém, instead of emulsion cooling, specially for cutting profiles and non-ferrous metals, neccessary supply of pressed air 6 Atm.
LASER LINE	Laser indicator of cut position.
LIGHT L1	Lighting of workink space.
PAL4	Packing on the palette 1,5m x 3,5m.
440-RDT 1000/600	Input or output robust roller table with a gutter which prevents leakage of emulsion on the floor, width of cylinders 600 mm, lenght 1000 mm, it is possible to put them for RDP or RDZ ,capacity 1000 kg/m.
440-RDT 2000/600	Input or output robust roller table with a gutter which prevents leakage of emulsion on the floor, width of cylinders 600 mm, lenght 2000 mm, it is possible to put them for RDP or RDZ , capacity 1000 kg/m.
440-RDM 2000/600	Input or output robust roller table with driven rollers . Driving by electrical engine, vormgearbox and inverter. By chain are driving cylinders. With 600 mm, lenght 2000 mm, capacity 1000 kg/m.
440-RDML 2000/600	Input or output robust roller table with driven lers. Driving from RDM throught chain. With 450 mm, lenght 2000 mm, capacity 1000kg/1m, working with RDM 2000/450.
440-RDP-2000	Input roller conveyer that is neccesary for making angle cuts and for connection to RDT,RDM, lenght 2 m, 7 rollers, bearing capacity 1000kg/m. Piece of equipment is also a connecting desk for connection with the vice.
440-RDPM-2000	Input robust connecting conveyer with the drive, there is a special shape for angle turning of the machine, with two tipping cylinders for angle turning of the machine (it is neccessary for cutting angle - 60°). Electroengine with the worm gearbox drives
440-RDPML-2000	Input robust connecting conveyer with driven rollers - riving from RDM 20000 throught chain. There is a special shape for angle turning of the machine (it is neccessary for cutting angle - 60°). With 600 mm, lenght 2000 mm.
440-RDZM-2000	Output robust connecting conveyer with the drive, there is a special shape for angle turning of the machine (it is neccessary for cutting angle + 60°). Electroengine with the worm gearbox drives three firm rollers and it is also the source of energy for
440-RDZ-2000	Output robust connecting conveyer, there is a special shape for angle turning of the machine (it is neccessary for cutting angle + 60°). With a gutter which prevents leakage of emulsion on the floor. Width of cylinders 600 mm, lenght 2000 mm.
440-RDZML-2000	Output robust connecting conveyer with driven rollers - riving from RDM 20000 throught chain. There is a special shape for angle turning of the machine (it is neccessary for cutting angle - 60°). With 600 mm, lenght 2000 mm.
500-RBR	Side support fixed cylinder, height 500 mm, with its own frame, it is mounted to roller tables RDT.
500-RBRS	Side movable cylinder for preparation of bundles, adjustable, height 500 mm, it is mounted to RDT, with own frame.
440-RDH	Independent movable cylinder, adjustable height, capacity 700kg.
440 V	Roller of roller table RDT pasted into gap.
OZP 1000	Mechanical fixed stop with ruler and scale line 1 meter long.
OZP 2000	Mechanical fixed stop with ruler and scale line 2 meters long.
OZP-D 1000	Mechanical fixed stop with digital displey 1 meter long.
OZP-D 2000	Mechanical fixed stop with digital displey 2 meter long.
OZS 2000	Electromechanical stop working with RDM roller table. It has two contacts. When material switches on the first contact, RDM slows down, after switching on the second contact, RDM stops.Digital displey of setting lenght.
OZS-D 2000	Electromechanical stop working with RDM roller table. It has two contacts. When material switches on the first contact, RDM slows down, after switching on the second contact, RDM stops.
OZP-L	2 meters long extension of OZP.
OZD-L	2 meters long extension of OZD.
440-QPARTS	Set of easy worn away spare parts: * 6 pcs: side vidia plates LNKW 19-1198000,HF10 * 6 pcs: screw for vidia plates US14 6 pcs * 4 pcs: bearing 6003 2RS * 20 pcs: cleaning brush 440 CK
440 - NAV	Manual instructions – printed version.

Operating data_79

Catalogue