300x320 SH-LR (II.GENERATION)
Semiautomatic machine with hydraulic manipulation.
The machine is designed for cutting of material in vertical and angle cuts, angle cuts are possible to set fluently from 60° right to 45° left.
It is suitable for piece production and small series production. Thanks to its robust construction it enables cutting of wide range of profiles and full materials.
- The machine is equipped with a control system PEGAS A2 relay logic
- Button control
- Control panel placed at the moving console for comfortable machine handling. There is equipped with a safety button, which stops the saw. There is also a feed regulator and buttons which control the various available movements.
- The machine is constructionaly designed in that way, so that it corresponds to extreme exertions in productive conditions.
- The arm of the machine is made of cust iron and it is designed to ensure the power and the precision of the cut. Arm is 25 grades sloped, it increases the lifetime of blade.
- The arm rotated by a shaft (joint) which is support by adjustableconical bearings
- Drive pulley and tighten pulley are both metal castings.
- Upper working arm position controled by automatic stopper (DPP)
- The down working position of the arm controlled by the miscroswitch. In the end position microswitch is on, arm goes to selected upper position.
- The vice is made from cast iron. Jaws ensure safe clamping of the material.
- Hydraulically operating vice with short travel is placed in an adjustable dovetail groove.
- Moving jaw of the vice is manual with a wheel and trapeze thread. Speedy jaw adjustment is achieved by means of a lever, spring and trapeze half-nut.
- Basic part of the vice moves according to the direction of the angle cut setting, fixation is made by the handle.
- Turn table is cust iron. A turntable gives a big place for supportion of material and its perfect clamping.
- Manuall turning of the table for angle cuts, angle fixation using handle. The turning table has autoarresting every 15 grades ( the groove with the spring ).
- General angles are adjusted by the nonius.
Basic equipment of machine:
- The blade leading in guides with hardmetal plates and leading bearings and along cast iron pulleys.
- There is a guide situated on the firm beam on the drive side. On the tightening side there is the guide situated on the moving beam.
- The guide beams of moving band guide is adjustable. Manual adjustment and fixing of the guide beams.
- The beam of the guide is moving in sliding leading.
- The saw-band is equipped with a guard, which protects the operator from millings and cutting emulsion.
- Mechanic tightening of the blade.
- Automatic indication of blade tension
- A passive driven cleaning brush for perfect cleaning and function of blade.
- Drive of machine is solved by worm gear box with pernament oil filling. Three phase engine with double winding, two cutting speeds. Termoprotection of engine.
- The cooling system distributes cutting emulsion to the band guides.
- Massive base with a tank for chips. Base is designed for manipulation manipulation with machine by pallet truck and also by any hight lift truck.
- Indication of blade tightening and opening of the cover.
- Controlling 24 V.
- Maschine is equipped with hydraulic system which ensures all functions of that maschine. It pushes the arm to cut, pulls up the arm and opens and closes vices.
Basic equipment of machine:
- Band saw blade.
- Set of spanners for common service.
- Manual instructions in eletronic form (CD).
After manual adjustment of the jaws the operator starts the cycle with a switch on the control panel. The hydraulic cylinder of the vice grips the material and the saw starts working. The cutting speed of the arm is controlled by a throttle valve. Arm and vice movements after cut finish following set user parameter. The vice opens and the operator can handle the material.
Semiautomatical control systém A2
Engine with the gear box- 2 speed
Measuring end stop which is mounted directly to the machine, length 1m.
Cleaning brush of blade, driven passively (driven by pulley).
Automatic end stop of the upper position.
Vice behind the cut. Hydraulic clamping of the material behind the cut.
Hydraulical upper vice. Hydraulic upper clamping tighten the material in vertical sense by the hydraulic cylinder.
Regulation press of vice.
Box for cutted pieces with emulsion draining to the waterproof tank.
Box for the chips with emulsion draining to the waterproof tank.
Tool for manipulation with BOX-PCS and BOX-TRI.
Lighting of working space.
Wasteless lubricating system, instead of emulsion cooling, specially for cutting profiles and non-ferrous metals, neccessary supply of pressed air 6 Atm.
Input connecting part of the roller conveyor RD - ensures angle cuts of the machine, length 1000 mm, width 390 mm, bearing capacity 200 kg/m, adjustable leg includedd in price.
Output connecting part of the roller conveyor RD-ensures angle cuts of the machine, length 1000 mm, width 390 mm, bearing capacity 200 kg/m, adjustable leg includedd in price.
Robust cylinder length 390 mm with the bearing for RD roller coneyor. The capacity of roller table increased from 200 kg/m to 400 kg/m
Side vertical fix cylinder, height 200 mm, monted on the RD tables
Side vertical moovable cylinder, height 200 mm, working only with RB.
Horizontal cylinder , working only together with RB + RBS for bundle fixing, length of cylinder 390 mm.
Mechanic measuring system with the meter L = 1200 mm.
Mechanic measuring system with the meter L = 2200 mm.
Mechanic measuring system with the meter L = 3200 mm.
Mechanic measuring system with the meter L = 4200 mm.
Mechanic measuring system with the meter L = 5200 mm.
Mechanic measuring system with the meter L = 6200 mm.
Mechanic measuring system with digital display 1 meter long.
Mechanic measuring system with digital display 2 meter long.
Mechanic measuring system with digital display 3 meter long.
Mechanic measuring system with digital display 4 meter long.
Mechanic measuring system with digital display 5 meter long.
Mechanic measuring system with digital display 6 meter long.
Second movable stop for OZ.
Support for RD.
Movable cylinder, adjustable height, width 390 mm, capacity 200 kg.
Set of easy worn away spare parts:
|300 - NAV|
Manual instruction – printed version.
Packing on the palette 1,2 m x 2,0 m.
Package - wooden box 1,2 m x 2,0 m.
Packing in the wooden cage.
Tech. data NO181-3 are valid on 1.1.2019. Producer has the right to make changes of technical data.
Values contained on this page are only for information purposes. This information is not an offer and is not a public promise. This indicative offer does not give right to close a contract. The only guiding document for the contract is a valid price list.